Thursday, December 31, 2015

ROLSEN TELEVISION SERVICE MODES

ROLSEN TELEVISION SERVICE MODES 

 Note: Do not change the values of other necessary parameters, this may lead to loss of the factory settings. To avoid the loss of factory settings:
Before changing the settings is better on a piece of paper to write down all the settings so you can go back to the original settings
MODEL : C1410, C1420, S2116, C2118, C2119 (dual-chip processor with the old TMP87CM38N)
C2112
FUNAI MK10
Log into the service menu can only be with a special service console.
MODEL : C2910, C2519, C2988
C1410, C1420, S2116, C2118, C2119 (two chips with the new processor CH08TO934)
C21R21, C2121, C2190, C21R90
C1420 (odnochipov)
C1425
Log in to the service menu as follows:
1. Set the volume equal to "O". (Required)
2. Press the button on the button "MUTE"
3. Hold down the "MUTE", press the "MENU" button on the front of the TV.
4. The screen will light up in the right corner the letter "D", and in the left corner of the displayed adjustable parameter and its value.
5. Pages menu change button "CAL"
Switching parameters are green and red buttons on a blue field panel. Change the parameters, yellow and blue buttons on a blue field.
MODEL : C1440,2146,2148,2139
Button "G +" on the TV and the "0" button on the remote control in standby mode.
MODEL : C72FDS107,109
# Press the first button [PRESET], then [TEST] Service console, on the screen in the upper right corner appears the letter M. To exit the service mode, press the [TEST] on the remote service. You can also exit the service mode by pressing the [STANDBY].
# Log in with a user panel: press [MENU], you will see the menu "Image". Press the number buttons [6] [4] [8] [3] on the remote control. In order to enter the service menu M1 ~ M4, press the corresponding number button on the remote. To access the service menu M5 ~ M0, press the button first [CALL] to exit the M1-M4, the screen will display the letter M, then subsequently press the [LOCK] (picture suitcase with a handle) and one of the number buttons [5 ] [6] [7] [8] [9] [0] to enter the menu M5 ~ M0. If you are in any menu M5 ~ M0, then go to another menu can be carried out without pressing the [LOCK], only the digital keys.
# In service mode by pressing the [- / -], you can enter a mode BUS OPEN. Pressing this button will exit this mode.
MODEL : C2131, C2133, C2150, C2192, C2195
 1. Log in to the service menu, you can use one of the following methods:
1.1.1. Using the service console
1.1.2. Having closed for a short time 1 and 3 pin terminal X2 through a resistor 2.2 ohms
1.1.3. Using a conventional remote control, press the following key combination:
# Reduce the volume to "0"
# Press the «menu»
# Select the icon "suitcase"
# dial series "5" "1" "7"
# Press the "green" button
2. A list of all the settings shown in Table no1
Exit the service menu by TV / AV button on the remote control. At the same time the recording in EEPROM All settings of the service menu.
MODEL : C2160, C21R65, C2165, C21R65

Log in to the service menu as follows:
1. Press the VOLUME DOWN button on the TV, after reducing the volume to "O", CLICK THE "DISPLAY ON REMOTE" while continuing to hold the volume down button on the front.
2. To exit the service mode, just turn off the TV
MODEL : C2135
The S2135 can be accessed with a conventional remote control.
It is necessary to open the remote, the nearest to the chip pad is not withdrawn under the button. If it bridged the TV enters the service mode