JBLGT5-A3001 CAR AMPLIFIER TROUBLESHOOTING AN D CIRCUIT DIAGRAM

CAR AMPLIFIER 

JBL GT5-A3001 

TROUBLESHOOTING AN D CIRCUIT DIAGRAM 

Installation Warnings and Tips
# Disconnect the negative (–) lead from your vehicle’s battery.
# At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas.
# Choose a safe mounting location away from moisture.
# Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself.
# Mount the amplifier, using the supplied hardware.
Speaker Output Connectors
# Connect the subwoofer to these terminals, observing proper polarity. Either + or – terminal may be used. Minimum total impedance is 1 ohm.
Fuses
# Replace only with the same type and rating.
Power Input Connectors
# +12V: Connect to the positive terminal of the vehicle’s battery. 8 AWG wire is recommended. Install an appropriate fuse holder and fuse (40A minimum) within 18 inches of the battery. Make sure the wire is not damaged or pinched during installation. Install protective grommets when routing wires through the firewall or other sheet metal.
Aux Output Connectors (RCA)
# Nonfiltered pass-through output. Connect to
the input of an additional amplifier.
Input Connectors (RCA)
# Connect to the RCA outputs from the source unit
or signal processor.
Input-Level Control
# Used to match the input level of the amplifier
to the output level of the source unit.
# See 9 for the adjustment procedure.
Protect LED
# Illuminated under any of the following fault
conditions: battery over/under voltage, short
circuit in speaker wires, amplifier is too hot,
amplifier’s output circuit has failed (DC voltage
is present in the amplifier’s output).
Low-Pass Filter Frequency Control
# 12dB/octave low-pass filter, variable from 32Hz to 320Hz.
# See adjustment procedure.
Power On LED
# Illuminated when the amplifier is on.
Setting Input Level
A Turn Input Level control counterclockwise to 6V (minimim).
With a dynamic music track playing, turn the head unit’s volume control to the 3/4 position. Turn Input Level control clockwise until the bass output is proportionate to the output of the high-frequency speakers, according to your preference. Input level is now adjusted correctly.
Setting the Crossover
Crossover setting for subwoofers.
Note: Acceptable frequency ranges are indicated in gray.
Troubleshooting
1. Status LED on Amplifier not Lit - Head Unit (Source) Turned ON
Verify:
A. Remote turn-on wire from source to amplifier has proper voltage
B. Power (B+) connections at amplifier, terminal blocks, and battery are secure
C. Ground (GND) connections at amplifier and vehicle chassis are secure
D. Battery B+ fuse (if used) is OK
E. Amplifier fuse is OK
F. B+ at battery and B+ at amplifier has proper voltage
2. Status LED’s Lit, No Output from Speakers in Normal Operating Condition
Verify:
A. RCA cables from amplifier to source are securely connected
B. Volume adjustment on amplifier is correctly adjusted
C. Source is ON and playing
3. Engine Noise From Speaker(s)
Turn source OFF, Disconnect RCA cables at amplifier. If noise stops, check equipment & cables leading to amplifier.
Verify:
A. RCA cables are of good quality with no breakage to internal shields
B. RCA cables from source to amplifier are not run alongside any power cables
4. Amplifier Output Distorted Music
Verify:
A. Source output music to amplifier is not distorted
B. Source output sensitivity is correctly adjusted
5. Amplifier Shuts Down, Green LED’s are Lit - Amplifier is in Thermal Protection Mode
Verify:
A. Amplifier is mounted with adequate air circulation around heatsinks or vents
B. Amplifier is not mounted under carpet or sealed enclosure
C. Speakers meet correct impedance for application (mono or stereo hookup)
6. Amplifier Does Not Turn ON, and Red LED is Lit Amplifier (and not Connected to a Shorted Speaker)
Verify:
A. Speaker crossover (if used) is not defective
General Capacitance Codebreaker Chart
pico-farad
(pF)
nano-farad
(nF)
micro-farad
(mF,uF or mfd)
capacitance
code
1000
1 or 1n
0.001
102
1500
1.5 or 1n5
0.0015
152
2200
2.2 or 2n2
0.0022
222
3300
3.3 or 3n3
0.0033
332
4700
4.7 or 4n7
0.0047
472
6800
6.8 or 6n8
0.0068
682
10000
10 or 10n
0.01
103
15000
15 or 15n
0.015
153
22000
22 or 22n
0.022
223
33000
33 or 33n
0.033
333
47000
47 or 47n
0.047
473
68000
68 or 68n
0.068
683
100000
100 or 100n
0.1
104
150000
150 or 150n
0.15
154
220000
220 or 220n
0.22
224
330000
330 or 330n
0.33
334
470000
470 or 470n
0.47
474








CIRCUIT DIGRAM 
CLICK ON THE IMAGE TO ZOOM IN