SAMSUNG UE32C5*** - UE37C5***- UE40C5*** - UE46C5*** - UE32C4000P
SERVICE MODE
Alignment Instruction
1. Usually, a color LED TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
7. To protect against shock hazard, use an isolation transformer.
1. Usually, a color LED TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
7. To protect against shock hazard, use an isolation transformer.
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote - control
Power OFF > INFO > MENU > MUTE > Power On
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote - control
Power OFF > INFO > MENU > MUTE > Power On
How to Access Service Mode
Using the Customer Remote
1. Turn the power off and set to stand-by mode.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
Using the Customer Remote
1. Turn the power off and set to stand-by mode.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State
Option
|
Control
|
SVC
|
Expert
|
ADC/WB
|
Advanced
|
T-TDT5DEUC-XXXX
T-TDT5DEUS-XXXX EDID SUCCESS CALIB : AV X COMP X PC X HDMI X Option : XXXX XXXX XXXX X
T-TDTDEU-XXX
SDAL-XXX RFS : P0155 T-TDT5DEUC 20XX-XX-XX TYPE : XX MODEL : XXXXX MAC Not Available FACTORY DATA VER : XXX EERC VERSION : XXX DTP-AP-COMP-XXX-XX DTP-HIIG-XXXX-X DTP-BP-XXXX DATE OF PURCHASE : XX/XX/XX |
How to enter the hidden factory mode.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced
6. Buttons operations within Service Mode
Menu
|
Full Menu
Display/Move to Parent Menu
|
Direction Keys UP/DOWN
|
Item Selection by Moving the Cursor
|
Direction Keys LEFT/RIGHT
|
Data Increase / Decrease for the Selected Item
|
Source
|
Cycles through the active input source that are connected to
the unit
|
White Ratio (Balance) Adjustment
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS, Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. (Refer to Table 1, 2) It varies with Panel’s size and Specification.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 "Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with that of the Master equipment.
- Set Aging time : 60min
- Calibration and Manual setting for WB adjustment.
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS, Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. (Refer to Table 1, 2) It varies with Panel’s size and Specification.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 "Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with that of the Master equipment.
- Set Aging time : 60min
- Calibration and Manual setting for WB adjustment.
USB Download Method
Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
1. Insert a USB drive containing the firmware
(T-TDT5DEUC) upgrade into the USB port on the rear of the TV.
2. Press the MENU button to display the menu. Press the UP or DOWN button to select "Support", then press the ENTER button.
3. Press the UP or DOWN button to select "SW Upgrade", then press the ENTER button.
The message "Scanning for USB. It may take up to 30 seconds." is displayed.
4. The message "Upgrade version XXXX to version XXXX? The system will be reset after upgrade." is displayed. Press the LEFT or RIGHT to select the "OK", then press the ENTER button.
Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade.
2. Press the MENU button to display the menu. Press the UP or DOWN button to select "Support", then press the ENTER button.
3. Press the UP or DOWN button to select "SW Upgrade", then press the ENTER button.
The message "Scanning for USB. It may take up to 30 seconds." is displayed.
4. The message "Upgrade version XXXX to version XXXX? The system will be reset after upgrade." is displayed. Press the LEFT or RIGHT to select the "OK", then press the ENTER button.
Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade.
Please check the firmware version after the
upgrades are complete. When software is upgraded, video and audio settings you
have made will return to their default (factory) settings. We recommend you
write down your settings so that you can easily reset them after the upgrade.
PCB layout
CLICK ON THE IMAGE TO ZOOM IN
