Friday, September 19, 2014

HOW TO ENTER SERVICE MODE TO SAMSUNG LE32D400E1W LE32D40*E2W LE40D50*F7W LED LCD TV - LE32D400E1W LE32D40*E2W LE40D50*F7W

Service Mode and Software Upgrade Procedure: UE40D500*BW  UE26D400*BW   UE32D400*BW  UE22D500*BW  UE19D400*BW  LE32D400E1W  LE32D40*E2W  LE40D50*F7W

SERVICE MODE (Factory Mode)
To enter ‘Service Mode’ Press the remote  control keys in this sequence: 
> If you do not have Factory remote control [INFO => Power OFF => Power ON =>  MENU => MUTE]
> If you have Factory remote  control; INFO => FACTORY KEY.
How to Access Service Mode
Using the Customer Remote
1. Turn the power off and set to stand-by mode. 1.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on. The set turns on and enters service mode. This may take approximately 20 seconds.
3. Press the Power button to exit and store data in memory.
If you fail to enter service mode, repeat steps 1 and 2 above.
Initial SERVICE MODE DISPLAY State.
How to enter the hidden factory mode.
# into the factory mode
# move the tap to Advanced
# key input : 0 + 0 + 0 + 0.  
 ** Hidden menu : Advanced.
Buttons operations within Service Mode.
Direction Keys▲/▼ (Item Selection by Moving the Cursor.)
Direction Keys ◄/ (Data Increase / Decrease for the Selected Item.)
Source => Cycles through the active input source that are connected to the unit.
USB Download Method
Samsung may offer upgrades for TV’s firmware in the future.  Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
1. Insert a USB drive containing the firmware.  (T-MSU4DEUC) upgrade into the USB port on the rear of the TV.
2. Press the MENU button to display the menu. Press the▲/▼ button to select "Support", then press the ENTER button.
3. Press the▲/▼ button to select "Software Upgrade", then press the ENTER button to select "By USB".  The message "Scanning for USB. It may take up to 1 minute." is displayed.  The message "Upgrade version XXXX to version XXXX? The system will be reset after upgrade." is displayed. 
4. Press the ◄/► to select the "OK", then press the ENTER button.
{Be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Please check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.}
How To Upgrade Sub Micom
Sub S/W (in Factory mode)
If you don't have DDC Manager, Use this method.
> Into the Factory Mode.
> Select "SVC". (Use button.)
> Select "MICOM UPGRADE off". (use  button.).  If message change from "off" to "wait", TV is upgrading Sub S/W. (It takes about 5 min.)
If update completes, TV set will booting automatically.


Tuesday, September 16, 2014

ENTONE URC-4 REMOTE CONTROL - HOW TO PROGRAM


How to program the Entone URC-4 _ Universal Remote Control
  The Entone Universal Remote Control v4.x (URC 4) is designed to work either on Radio Signals (RF) or Infrared (IR).   It can control Janus Media Hub using RF from another room where is not at direct sight distance from the Janus.  Janus is a multi-television media hub. It can support multiple outputs in multiple rooms viewing different channels or TV programs. Amulet is a single output video receiver. You can connect Amulet to a primary output only. You can use RF URC 4 to control Janus/Amulet using radio signals (RF). These radio signals travel over long distances and go through walls and other solid objects. You must connect the Remote Antenna Package (RAP) to the rear panel of the Janus/Amulet.  Janus/Amulet comes with one IR URC 4 to be used for output 1 (primary). (Additional RF URC 4 can be purchased separately.) Your RF URC 4 must be registered to one of the 2 outputs (primary or secondary) before it can be used. One RF URC 4 can only be registered to one output. However, you can register at most 3 RF URC 4 to an output. After registration, you need to use the corresponding RF URC 4 to control the outputs.
  Each output allows a maximum of 3 RF URC 4 to be registered and a registration list is maintained. If the user has registered 3 RF URC 4 and tries to register another RF URC 4, the first registered RF URC 4 will be removed from the registration list. This works as a first-in-first-out fashion.
  Each RF URC 4 can only be registered for one output. If user tries to register a RF URC 4 which is already registered to another output, that remote registration will be removed from the original registration list.
  The registration list is maintained in order. If the secondly registered RF URC 4 is removed from the list, the third entry will move forth to the second and the third will be blank for a new RF URC 4 to be registered.  You must install the Remote Antenna Package (RAP) comes with Entone Second Stream Kit before doing the registration.
RAP Installation (in remote room)
* Plug the RAP into the TV.
* Connect the TV coax cable to the RAP and the TV coax network wall outlet. { If your URC 4 isn’t working very well from far away , you may be experiencing interference from objects near your receiver. To improve your URC 4’s reception range, try to adjust the antenna orientation.
Connecting STB to the TV coax network
Janus without Tuner Connection: Connect the Janus “MATV” or “TV OUT” output to the TV coax network.
Connect the Janus “MATV” or “TV OUT” and “RF IN” or “CABLE/ANT IN” output to the TV coax network.
Connect the Amulet “REMOTECONTROL” and “COAX” or”TV OUT” output to the TV coax network.
RF URC Registration.
* Press and hold the “OK” button on the STB front panel for 5 seconds until the touch panel backlightis flashing. The STB is now in URC registration mode. [If registration is not completed in 30 seconds, the touch panel backlight will stop flashing.]
* Press “STB” button once on the URC.
* Press and hold the “STB” button on the URC for 5seconds until the “STB” button backlight is on.
* Press “STB” button once again. Both the “STB” and “AUX” button backlight will illuminate.
* Press “1” or “2” to register the URC to output 1(primary) or output 2 (secondary) (depending on the middleware). Upon successful registration, the STB POWER indicator will flash once and the touch panel backlight will stop flashing.
  The POWER key can be configured to control both the STB and TV while the URC 4 is in “STB” mode, please refer to the section “Toggle Power Key Punch-through Functionality” in Chapter 4 for details.  The Volume +/- and MUTE key can be configured to control both the STB and TV while the URC 4 is in “STB” mode.
Controlling STB using IR URC
On the URC 4, press and hold the “STB” button for approx. 5 seconds. The “STB” button backlight will illuminate. Now the URC 4 is in registration mode.
On the URC 4, press “STB” once again. Both the “STB” and “AUX” button backlight will illuminate.
  Press “0” to set RF URC 4 to IR mode only. The RF URC 4 will not send any RF signal.   The “STB” button backlight on the URC 4 will blink twice to indicate that the setting was successful. Pressing  a  key  other than “0”, “1”,  “2”, “3”  or  a  button  is  not  pressed  within  30  seconds, the  “STB” backlight  will  blink  rapidly  for  7  times  to  indicate  an  error  and  then  extinguish,  and  the  URC  4 registration process will be terminated.
Controlling Your Television and other A/V Devices
  The POWER key can be configured to control both the STB and TV while the URC 4 is in “STB” mode.
  The Volume +/- and MUTE key can be configured to control both the STB and TV while the URC 4 is in “STB” mode.
To Program a TV or AUX device.
* Locate the device code for your desired device in the device code table provided in the Appendix. If you could not find the device code for your device or it does not work after trying the listed device codes for your device brand, then you can go to the next section to try the auto search procedures.
* Turn on your device and with media inserted (if applicable).
* On the remote control, press a device mode key for 5 seconds (i.e., “TV” or “AUX”). The device mode key will light up. [NOTE: Use the “AUX” mode key to program control of VCR, DVD player, cable box, satellite set-top box and audio device.]
* Enter the four-digit device code for you device. If you perform this procedure correctly, the selected device mode key back-light will blink twice. [NOTE: If you enter an invalid device code, the selected device mode key will fast blink 7 times. Device program mode will be terminated.]
* Aim the remote control at your device and press the “POWER” once. The device should be turned off. If it does not respond, repeat the above steps.
NOTE: In the programming mode if no key is received with in 30s, the device mode key back-light will blink rapidly for 7 times to indicate an error and then extinguish, and the programming mode will end.
Toggle Power Key Punch-through Functionality
By default, if the remote control is in STB mode, the URC Power button switches STB off ONLY. To control the URC Power button functionality to switch off either both the TV and/or STB, do the following:
* Press and hold the “STB mode key for 5s. The “STB” device mode key backlight will light up.
* Press “POWER” key once.
* Either do the following:
# Press 1 to control both the STB and TV, OR
# Press 0 to control the STB ONLY
NOTE: In the programming mode if no key is received with in 30s, the device mode key back-light will blink rapidly for 7 times to indicate an error and then extinguish, and the programming mode will end.
Toggle Volume Key Punch-through Functionality
By default, Vol +/- and MUTE keys are sent to STB only when URC is in STB mode. Punch-through function for those keys is enabled at the same time when programming the device code for TV or AUX. That is:
* If user program device code for a TV device, the punch through function will be configured for TV at the same time.
* If user program device code for an AUX device, the punch through function will be configured for AUX at the same time.
To disable the Punch-through function for those keys, do the following:
* Press and Hold STB for 5 seconds, then STB led will switch on.
* Press STB key once again, then both STB and AUX led will switch on.
* Press 0
Auto Search Procedures
If your device does not respond to the remote control after trying all devices codes listed for you brand, or if your brand is not listed at all, try searching for your device code as follows:
* Turn on your TV or your A/V device.
* On the remote control, press a device mode key (i.e., “TV” or “AUX”) and hold for 5s. The device mode key will light up.
NOTE: Use the “AUX” mode key to program control of VCR, DVD player, cable box, satellite set-top box and audio device. 3.  Press the “POWER” key once.
* Aim the remote control at the device. Press either the “CH UP” key or “CH DOWN” key to do device auto-scan:
# Press the “CH UP” key to start searching upward at an approx. 5 seconds interval for each device code. The TV/AUX mode key will be on and blink every 5 seconds while in the device scan mode.
NOTE: In this search mode, the remote control will send  IR codes from the library starting from the lowest code set number to the end of code set for that device; OR
# Press the “CH DOWN” key to start searching downward at an approx. 5 seconds interval for each code set. The TV/AUX mode key will be on and blink every 5 seconds while in the device scan mode.
NOTE: In this search mode, the remote control will send IR codes from the highest code set number to the beginning of code set of that device.
* If the device turns off, a working code has been found. Press OK once to lock in the code. The selected mode key will blink twice
* If all code sets of that device is exhausted in the search and the OK is not pressed, the selected device key will fast blink 7 times and the search mode will be terminated.
NOTE: During the auto-scan, you can press “UP” arrow or “DOWN” arrow to advance to the next device code immediately without waiting for 5 seconds. You can also use “UP” arrow or “DOWN” arrow to change the direction of the search.
NOTE: In the programming mode if no key is received with in 30s, the device mode key back light will blink rapidly for 7 times to indicate an error and then extinguish, and the programming mode will end.


Monday, September 15, 2014

HOW TO ENTER SERVICE MODE AND ADJUST ITEMS – KONKA KDL26BZ31U - KDL32BZ22U

APPLICABLE TO KDL26BZ31U - KDL32BZ22U - KDL32BZ23U - KDL32BZ25U - KDL32BZ25U-A - KDL32BZ31U - KDL37BZ23U - KDL37BZ25U - KDL37BZ25U-A - KDL37BZ31U - KDL42BZ23U - KDL42BZ31U - KDL42BZ25U-A

 FACTORY MODE ADJUSTMENT
The way to enter factory menu
> Press “Menu” button and then press “Pre.Ch” button five times, you can enter the factory       menu, and the software version information is shown in the last line.
> The way to exit factory menu
> Press “Exit” to exit the factory menu, the value you have changed will be save automatically.
factory menu operation method
> Press the▲/ to select the item you desired change, and press “OK” to set the value.
White calibration adjustment
> Receive black or white signal under AV or PC mode, adjusting brightness and contrast to set the brightness to 5 Nit in dark area and 90 Nit in bright area.
> Adjust white balance. Enter factory menu, select “White Balance” item, enter to the  White Balance Adjust Menu.
Adjust WBRO 0-100
WBGO 0-100
WBBO 0-100
WBRG 0-100
WBGG 0-100
WBBG 0-100
Adjusting chroma coordinates of black and white to fit the requirement. 
* Cool (9300K) x=0.283±0.015 , y=0.297±0.015
* Normal (7500K) x=0.299±0.015 , y=0.315±0.015
* Warm (6500K) x=0.313±0.015 , y=0.329±0.015
* Gamma Table Loading
Enter factory menu, select “White Balance” item, and press “OK” to set the value.
Burn on
When source is in TV mode, select the item of “Burn On” in factory menu, keep the state for “On” by pressing “OK” button. After putting on the burning switch, the TV set will be boot up straightly and keep in the snowflake burning on state if you put on the power supply. Here, the function that auto power-off after in 15 minutes while no signal input will be invalid. When the burning on finished, please change the “Burn on” state to “Off”.
No Signal Time off
Select the item of “No Signal Time off “in factory menu, press “OK” to set the value (2/5/10/15 minute), the default value is 15 minute.
Parameters Setting
Select the item of “Parameters Setting” in factory menu, press “OK” to enter Parameters Setting  Menu. Then you can set some value for volume and image features.
Auto Color
Select the item of “Auto Color” in factory menu, press “OK” to start auto adjust the color.
Advanced Video Menu
Select the item of “Advanced Video Menu” in factory menu, press “OK” to enter Advanced  Video Menu. Then you can set some value.
AGC
Select the item of “AGC” in factory menu, press “OK” to set the value (0/1/2/3/4/5/6), and then choose the value for the best image effect.
Pre-Channel Setting
In factory menu, select the item of “Set Default Channel”, and press “OK” button.
Software Resetting
In factory menu, select the item of “Set Default Value” , press “OK” button and turn off   TV, then turn on. This operation can clean up all data that modified by users, and make the data 
go back to default settings.

Friday, September 12, 2014

HOW TO UNLOCK LG DVD PLAYERS - REGION FREE

HOW TO MAKE LG DVD PLAYERS REGION FREE
  LG 2002 / 2230P / 2240N / 2300 / 2310P / 2330P / 2380P / 3000P / 3030N / 3030P / 3200 / 3200E / 3251P / 3315E / 3350E / 3351 / 3351E / 3351P / 3520 / 3525 / 3530 / 3630 / 4020N / 4220 / 4593 / 4710 / 4721P / 4750 / 4730 / 4821P / 4830 / 4921P / 4941P / 4959 / 5502 / 5502P / 5620 / 5630 / 5772N / 5812N / 5822N / 5822P / 5850A / 5921N / 5930 / 5942E / 593NW / 593W / 5942E / 5942P / 595NWQ / 596M / 6043 / 6053 / 6230 / 6812P / 7352N / 7911N / 884B / DA3520 / DA3530A / DA3620 / DA3630 / DA5630 / DC-365 / DC-489 / DC-596M / DC-593W / DC-596B / DC-784M / DE-8421P / DF8900P / DF9921N / DF9921P / DGK585XB / DK5922P / DK-7711P / DK-7821P / DK7942P / DK9923N / DK9923P / DKS-5000 / DKS-6000 / DP9911P / DS375 / DS563X / DT-585 / DT-777W / DV-6842P / DV-7821 / DV-7942P / DV-8621P / DV-8651C / DV-8700C / DV-8721P / DV-8743P / DV-8900C / DV-8921N / DV8931H / DV9723P / DV9823P / DVCR-2002 / DVD4710 / F-DV25 / FDV55 / LH-C6231 / VD4730 / LH-D6240 / LH-D6245 / LH-D6246 / LH-T6340 / LHT6345 / LH-T6540 / V-692W / V782NWK / V782W / V8706 / V8716 / V8824W / V9120W / V9800 / V88060VX / VD4730
* Power on (with no disc inserted)
* Press PAUSE
* Press 3, 1, 4, 1, 5, 9
* Enter the desired RC
* Press PAUSE
* Turn the player off and wait a few seconds.

# VCD playback
# Press PAUSE, 1, 4, 7, 2
# Press UP 6 times, '07 00' should appear on the display
# Press Program 6, Program 5 ('07 FE' should be displayed)
# Press ENTER
# Press RETURN
# Power off and on again.
  LG 3620 / 5063 / 5073 / 5083 / 5084 / 5095 / 5174 / 5183 / 5184 / 5193 / 5195 / 5253 / 5353 / 5930 / 5931 / 5935 / 6033 / 6053 / 6054 / 6183 / 6188 / 6193 / 6194 / 6195  / 6196 / 6353 / DR250 / DV1000 / DV2000 / DV7832NXC / DVB418 / DVC8700 / DVP-S500 / DVP7772 / DVS-7720 / DVS-7920 / DVS-7800 / DVT418 / LDA-511 / LDA-530 / LDA-531 / LH-CX247W / LH-CX440 / LH-D6230 / LH-D6235 / LH-D6430 / LH-D6530D / LPA-534 / DP8821 / DP9821P / DV-8700H / DV-8600 / DV-8631V / DV-8700A / DV-8700H / DV8761 / DV-9700 / DV-9800H / DV-9900 / DVC9800 / DVD-8742X / DVX-171 / DVX-173 / DVX-9700 / DVX-9900 / DVK-9913N / DVX-7900 / DVX-8651C / DVX-8751C / DVX-8851 / DVX-9700 / DVX-9843 / DVX-9900 / DZ9311N / DZ9700 / DZ9811P / DZ9900 / LH-SW5200 / LH-T1000 / LH-T250 / LH-T252SC / LH-T751TB / LST-3510A / LXD-5230 / NS8421T
* Turn on the player (without disc inserted)
* Open the disc tray
* (Press PAUSE)
* Press 0, 0, 0, (0)
* Enter region (1-6; 0=region free)
* (Press PAUSE)
* Turn it off.
  LG DR-4810 / DR-4912 / DR-4922 / DR-6621 / DR-6921 / DR-7400 / DR-7500 / DR-7621N / DR-7800 / DR-7900MH / DR-7922W / DR4812W / HDR589X / LGR435 / LGVR435 / LRA-516 / LRA-536 / LRA-537 / LRA-539 / LRY-517 / RC-6800 / RC-68223 / RC-6921W / RC-7000 / RC-7300 / RC-7723W / RC6821W / RH-177 / RH-188H / RH-199H / RH-4810 / RH-4820 / RH-4820W / RH-4840 / RH-4920 / RH-4940 / RH-7500 / RH-7521W / RH-7624W / RH-7800 / RH-7800H / RH-7823W / RH-7900H / RH-7900MH / RH-7926W / XBR446 

* Open the disc tray
* (Press SETUP and scroll to 'Lock')
* Press 0 seven times
* (Press ENTER, Setup).
{LG DVD-8742X}
* Press STOP for 5 secs to set Progressive Scan on or off (no disc in tray)
* Press PAUSE Pause for 5 seconds to switch between NTSC / PAL
To change the Region; see above.

Thursday, September 11, 2014

HOW TO UNLOCK PARENTAL LOCK - V-CHIP LOCK - TO TVs


Unlock Procedure to Locked TVs and other devices.
GE TV sets
RCA and GE TV sets use a four digit code to control the v-chip. The code reset is different depending on the model. Try each number until you find the one that works for you.
* Hold down the MENU button on the remote and VOLUME DOWN button on the TV it’s self at the same time for at least 4 seconds. 
* The set won't say so, but the lock will be unlocked.

# Hold down the 0 (zero) button on the remote and the VOLUME DOWN button on the TV itself at the same time for at least 4 seconds. 
# The set won't say so, but the lock will be unlocked

* Hold down the MENU button on the front of the TV and the TV button on the remote at the same time for at least 4 seconds. 4- Hold down GO BACK button on the remote and MENU button on the front of the TV at the same time for at least 4 seconds.

* Hold down EJECT button on the front of the TV set and the MENU button on the remote at the same time for at least 4 seconds. Depending on the model, one of the methods should unlock the V-chip. Now, if desired, you can change the settings on the V-chip by going to the MENU and going to PARENTAL CONTROLS, or on some sets, going to MENU and then going to TV SETUP, then to V-CHIP SET.
MITSUBISHI
Mitsubishi sets use a four-digit code for a V-Chip locked program, view a locked TV, cancel the lock, or to enter the V-Chip lock menus. 
You can view the locked shows on the TV set by pressing the number 9 and QV buttons on the remote at the same time, whenever your code is requested. This process temporarily unlocks the TV and asks you to enter a new code.
RCA
* Hold down MENU on the remote and VOLUME DOWN on the TV it’s self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked
* Hold down the 0 on the remote and the VOLUME DOWN buttons on the TV its self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked
* Hold down the MENU button on the front of the TV and the TV button on the remote at the same time for at least 4 seconds.
* Hold down GO BACK on the remote and MENU on the front of the TV at the same time for at least 4 seconds.
* Hold down EJECT on the front of the TV and the MENU button on the remote at the same time for at least 4 seconds.

(Depending on the model, one of the methods should unlock the V-chip. Now, if desired, you can change the settings on the V-chip by going to the MENU and going to PARENTAL CONTROLS, or on some sets, going to MENU and then going to TV SETUP, then to V-CHIP SET.)
PHILIPS & MAGNAVOX
Philips sets use a four digit code to control the v-chip. 
The override code for Philips sets is 0711, although it may say "Incorrect code" the first time to trick you. 
If "Incorrect code" is displayed, simply enter 0711 again. 
To use it hit the MENU key to get to the menus. 
Go up or down until you reach AUTOLOCK or SMARTLOCK, depending on the model, and push the "right arrow" key on the remote. 
Enter the override code, and enter it a second time if it says it is incorrect.  Once in the AUTOLOCK or SMARTLOCK menu, go to BLOCK, and push the "right arrow" key. 
Go to BLOCKING OPTIONS and press the "right arrow" key. Go to MASTER DISABLE and press the "right arrow" key so that it says "MASTER DISABLE ON". The v-chip is now reset.
TOSHIBA TVs & COMBOS
* Disconnect the AC power for at least one minute to reset the clock.
*
Adjust the volume to the minimum using the Volume down button on the front of the unit.
* Press and hold the Volume down button on the front of the unit and the 0 button on the remote control at the same time, holding them down for at least 10 seconds.  The user menu will appear with the V-Chip cursor blinking.
* Press the ENTER key on the remote control and the NEW PASSWORD menu will appear.
* Enter your new password.
PIONEER PLASMA TVs
Pioneer plasma set use’s a four digit code to control the v-chip. 
To reset the Pioneer:  
First put the media receiver in the standby mode, then hold down the CLEAR button and press STANDBY/ON button on the plasma display. The device should now be reset. 
If you want, you can run an auto install to configure your device. 
Turn on the power, press MENU, select SETUP on the screen, and press ENTER. If it asks for a secret number, you need to reset the device again and start over. 
Otherwise, scroll to AUTO INSTALLATION and press ENTER.
LG
When you are asked for the code, enter 7,7,7,and then 7.
APEX DIGITAL
Apex TVs use a four digit code to control the v-chip. The override code for many models is 6688. Other sets may not have one, or may have a default code of 1225 instead of an override code.
To use the override code:
* Hit the MENU key to get to the menus.
* Go down to the SYSTEM menu and hit the right arrow on the remote control.
* Once in the SYSTEM menu, go to PARENTAL GUIDE. It will ask for your code.
* Enter the override code listed above. From here, you can turn on and off different rating restrictions, as well as set a new code.
{No matter what the V-chip code is set to, the override code will still work. If you have a blank screen with a red key on the bottom left, simply press the (function or F) button and the mute button at the same time. This will unlock the screen and allow you to view the channel as desired}
PANASONIC Factory Default & Reset
Panasonic sets need to be reset to clear the v-chip settings. 
To do this, put it in standby mode, then press the POWER and ACTION buttons at the same time and then turn the power off. 
The set should reset to the factory defaults, and reset the v-chip.
SINOTEC
If you have the original remote (RC-A07) for Sinotec TV, then press and hold down the Music button for about 10 seconds.
DISH NETWORK RECEIVERS
Some boxes can be reset by unplugging the box, and while holding down the power button, plug the unit back into the wall receptacle and then release the power button. 
Then, let the box do its thing.
Other Dish Network receivers you can reset by first pushing the MENU button, then push "6, 3, INFO, right arrow, left arrow button, TV/VIDEO", then unplug the receiver and plug back in.
PS2

When you try to use a DVD that is blocked, it will ask for your code. 
Press SELECT on the controller. 
Enter the deletion code 7444 when prompted. You can then set a new lock code. Next, remove the disk and then turn off your PS2.
X-BOX
To reset the X-Box code, go to the settings screen from the dashboard. 
From there, go to PARENTAL CONTROL. 
Instead of entering the code, press the following button combination: X, Y, LEFT TRIGGER, X, you will then enter into the PARENTAL CONTROLS screen where you can set a new code, or disable the parental lock.
QWESTAR
Simply enter the code 3308
CherryBoo to the Rescue
The V-Chip is bypassed by holding the zero key on the original remote hand unit, and at the sane time holding down the volume down on the front of the TV set. 
This should reset the oide so you can enter a new one.
SONY LCD TVs
When prompted for the code, enter the master reset code: 4357. This code will reset the master code.
AIWA TV COMBOS
With the TV turned on, simultaneously press VOLUME down button on the front of the TV set and the number 7 button on the remote control to reset pin code and customer ID.
MATSUI
Turn off for 30 minutes. 
Then turn back on and on the front of the unit, NOT THE REMOTE UNIT, press channel up and record together and that should bring the screen back on.
OPTIMA
Simply enter the code 3308
SYMPHONIC TVs & COMBOS
When you are prompted to enter an access code, enter 0000


HOW TO PROGRAM SHARP VC-H982 UNIVERSAL REMOTE CONTROL




with this Universal Remote Control, you have instant control over virtually any TV anywhere in the world.  
All you do is simply hold the mute button for 5 seconds and you have total control to change channels, turn volume up or down, power on or off, or mute.  There is NO need to enter a confusing universal remote code for each television.
PROGRAMMING PROCEDURE AND SET-UP CODE LIST - SHARP VC-H982 _ UNIVERSAL REMOTE CONTROL
SET-UP PROCEDURE
* Point it at a TV set and press the Mute/Power button. (Mute button if TV is already on, or Power button if the TV hasn't already been turned on)
* Keep pointing it at the TV until the TV turns on or muted, most TVs respond in about 5 seconds, the most is up to 20 seconds.
* Once the TV is muted or turns on, simply let go of button and you have total control. You can use the remote as if you had the original remote, and respond instantly. 

SET-UP CODE LIST
TVs
Emerson 18
Fisher 16
Funai 05
GE 06, 08
Goldstar 17
Hitachi 14
JVC 15
Magnavox 08, 10
Mitsubishi 13
Panasonic 12, 20
RCA 06, 08
Samsung 19
Sanyo 16
Sharp 01, 02
Sony 09
Technol Ace 03
Toshiba 11
Zenith 04, 07

Cable Box codes
Jerrold 01, 04, 05, 06, 07, 02, 03, 08
Oak 16
Panasonic 13, 14
Phillips 18
Pioneer 15
RCA 13, 14
RCA SAT 19
Regal 17
Scientific AT 09, 10, 11
Sony SAT 20
Zenith 12

Monday, September 08, 2014

HOW TO ENTER SERVICE MODE TO ZENITH BRAND TVs

# Turn the TV on.
# Hold down the MENU button on remote until the on-screen menu disappears or "Welcome Message" appears then release the MENU button and within two 2 seconds press the following five buttons:
9 8 7 6 ENTER or 9 8 7 6 DISPLAY

# The Service Menu will be displayed.
# Using the remote control buttons:
MENU > Toggles between two menu pages.
UP/DOWN > Selects the item for adjustment.
LEFT/RIGHT > Varies the value
POWER > Exit service mode and saves adjustments made.

# Service Menu -1
Press and hold the MENU button on the remote and the MENU button on the TV at the same time, until the first Service Menu is displayed.
# Service Menu -2
Repeat the above sequence:
Press and hold the MENU button on the remote and the MENU button on the TV at the same time, until the second Service Menu is displayed.
# Press and hold the MENU button on the remote and the MENU button on the TV at the same time
# If a password screen comes up: Press and hold the MENU button on the remote and the MENU button on the TV at the same time again, until the Service Menu is displayed.
# Press and hold the MENU button ON THE REMOTE until a 4-digit password screen is displayed.
# Then try any of the following codes to access the Service Menu:
0 0 0 0
7 7 7 7
8 7 4 1
# Press and hold the MENU button ON THE REMOTE. (The menu on the screen will disappear)
# Now Press and hold the MENU button ON THE PANEL.
# Keep both buttons pressed until the Service Menu is displayed, and then release the 2 buttons.
# using the remote control buttons:
MENU > Toggles between two menu pages.
UP/DOWN > Selects the item for adjustment.
LEFT/RIGHT > Varies the value
POWER > Exit service mode and saves adjustments made.